Audio Selector Enclosure for 3.5 mm Jacks (November 15, 2026)
English Français
Antre du Tryphon
Search
Mini Solder Spool

Mini Solder Spool

May 1, 2020 · claude 3D Printing
Soldering electronic components using a large solder spool of 454 grams or so is quite inconvenient even if it is mounted on a solder spool holder. I prefer to wind a small amount of it on a smaller spool. This is what this mini solder spool is for....

Pull Handle

Pull Handle

April 24, 2020 · claude 3D Printing
This is a simple pull handle. A #10 flat head screw is recommended to fasten it.

TRENDnet TK-409K KVM Holder for Ikea Ivar

TRENDnet TK-409K KVM Holder for Ikea Ivar

April 18, 2020 · claude 3D Printing
This is a holder for a TRENDnet TK-409K KVM. The holder is hanged on a unit side of the Ikea Ivar shelving system. The TRENDnet TK-409K is a 4 ports Keyboard/Video/Mouse switch.

Parametric Bumper Feet

Parametric Bumper Feet

April 10, 2020 · claude 3D Printing
This is a simple OpenSCAD project that generates bumper feet for various objects. It was specifically designed to replace the lost bumper feet of a Falcon Print Trimmer. Printing it using TPU is the best way to go. A sample is included. To create a...

Nuvistor Display Stand

Nuvistor Display Stand

April 4, 2020 · claude 3D Printing
This is a display stand for an old electronic part: the Nuvistor which is a type of vacuum tube. It was announced by RCA in 1959.

ESP8266 Motion Sensor Case

ESP8266 Motion Sensor Case

March 27, 2020 · claude 3D Printing
This is a case for a motion sensor based on the ESP8266 and the HC-SR501, a PIR (motion) sensor.

4 inches x 0.7 inches Label Holder

4 inches x 0.7 inches Label Holder

March 20, 2020 · claude 3D Printing
This is a paper tag holder made out of 4 inches (10.1 cm) x 3 inches (7.6 cm) index cards. They fit an edge of about 1/4 (6.25 mm) of an inch wide. A piece of size 4 inches (10.1 cm) x 0.7 (1.75 cm) inch out of the index card fits well.

Hanging Buckets for Power Supplies

Hanging Buckets for Power Supplies

March 14, 2020 · claude 3D Printing
This kit of objects is two hanging buckets set for a cheap bench power supply. One bucket is 100 mm deep. The other is 50 mm deep. They are held together by two arms that you must glue to the buckets. The buckets are 84 mm apart.

Ikea Bror Caster Holder

Ikea Bror Caster Holder

March 7, 2020 · claude 3D Printing
This object lets you install casters to a Bror workbench. It is designed for 1-7/8" (48.5 mm) x 2-9/16" (65.5 mm) casters. The holes for the bolts are 2-1/8" (54 mm) x 1" (25 mm) apart. The bolts I used are 1/4" (6.25 mm) in diameter, 1/2" (12.5 mm)...

Ikea Ivar Vesa 100mm Mount

Ikea Ivar Vesa 100mm Mount

February 29, 2020 · claude 3D Printing
This is a 100 mm VESA mount designed to be mounted on the Ikea Ivar side units. As shown on the picture, I have used it to mount a small monitor.